Total 21 job vacancies by P-con Management Pte. Ltd.

a) Minimum Degree in Civil Engineering recognised by PEB

b) Registered Resident Engineer by IES

c) Min. 10 years experience in building work

1. To act as a Site Supervisor appointed by the Qualified Person (QP) in accordance with the Building Control Act.

2. To assist the QP(Supervision) in carrying out supervision works on site

3. To prepare inspection and test plans which are relevant for the supervision of the projects.

4. To conduct quality control of all civil and structural, as well as, mechanical, electrical, and landscaping works.

5. To inspect and advise for compliance on temporary works, including instrumentation reports by Contractor.

6. To support in public relations works.

7. To supervise and keep independent records of day works including overall and part works programme.

8. To issue site memo to Contractor for recording of observed safety and quality non-compliance with Contract or Authorities, Services Agencies requirements.

9. To attend project meetings and draft meeting minutes.

10. To carry out site supervision and inspection of works including any off-site manufacturing/testing as instructed by the QP(Supervision) and/or S.O. so as to ensure that works are constructed to the required quality, accuracy and standards.

11. To monitor progress of the works on site including material supply to the site and at any off-site manufacturing/testing facilities and report delays immediately.

12. To provide standing supervision in compliance with the relevant Building Control Regulations.

13. To maintain proper and updated daily records of all works done, including independent record of test, inspections, status of work, safety, site diary, material and equipment on site, labour, dayworks, provisional quantities etc.

14. To check that the Contractor executes preliminary items.

15. To check service routes and Contractor’s setting out and report any deviations to the QP(Supervision)/S.O.

16. To verify reports and claims submitted by Contractors.

17. To record all variations as instructed or approved by the S.O.

18. To undertake any other duties related to the project as and when instructed by the S.O./Client/QP(Supervision).

19. To check drawings including as-built and documents and report discrepancies.

20. Report on site safety, security and housekeeping.

21. Verification of the Client’s Permit To Works (CPTW) checklist completed by the Contractor including:

i. Review the CPTW and keep records of relevant documents such as Authorities/Agencies

approvals, services detection plan and etc. on site.

ii. Make yourself aware of the contractor daily site works and remind them to provide the CPTW

for your verification prior to commencing works on site.

iii. Inform the Contractor in-writing of any non-compliance identified by the CPTW and ensure that

the Contractor rectify the non-compliance prior to permitting works to commence.

iv. Inform the S.O./ QP(Supervision) immediately if the Contractor proceeded works on site without a valid CPTW.

22. Any others duties specified under Building Control Acts and relevant scope

23. Any other work incidental to the above and/or reasonably to be inferred from the nature of work to be carried out by the Service Provider Field staff; and,

24. Such other work as may be agreed from time to time.

25. In addition to the principal duties detailed above, the Field Staff is expected to be vigilant and monitor the Contractor performance in progress, site safety, services protection, security and hygiene.

The RTO Shall:

1) Have a Diploma in Civil/ Structural discipline or National Certificate in Construction Supervision (NCCS) or equivalent and shall be accredited by JAC of IES/ACES as QSS; and

2) Have Minimum three (3) Years of relevant experience in projects similar in nature to be Works in the Civil Contracts.

DUTIES AND RESPONSIBILITIES OF SITE SUPERVISORY STAFF

As a guide, the duties and responsibilities of the site supervisory staff is outlined below. The list does not purport to completely embrace the duties expected and the site supervisory staff ought to exercise his discretion to go beyond what is stipulated herein when carrying out his duties.

1) GENERAL

a)To carry out site supervision and inspection of the works including any off-site manufacturing as instructed by the consultant team to ensure that works are constructed to required quality and accuracy.

b)To study the contract documents and drawings and verify if there are any discrepancies among the drawings. All discrepancies shall be brought to the attention of the Consultants concerned.

c)To provide standing supervision as and when directed by the consultant team.

d)To ensure that all installation methods and material used are in accordance with the contract drawings and specifications.

e)To liaise with the contractors and the Architect / M&E / C&S Engineer in the checking and approval of shop drawings, catalogues, and samples.

f)To liaise with the contractors in the coordination of site works & resolve site installation problems.

g)All problems on site shall be referred immediately to the C&S Engineer /Architect / M&E . The Resident Engineer sahll issue sketches or directions as and when necessary. All site memos shall be copied to the Consultants.

h)To monitor and ensure that the site programme is in accordance with the approved construction programme. Any deviations from the construction schedule shall be reported immediately to the C&S Engineer /Architect / M&E. In the event of delays, the Resident Engineer shall assist the contractors to mitigate delays but without comprising on the quality.

i)To ensure that the contractors maintain work safety, cleanliness, and tidiness of the site.

j)To ensure that the main contractor and sub-contractors comply with the Ministry of Manpower’s guidelines and recommendations for construction safety and the owner’s in-house safety management system.

2)GENERAL

a)To check on site that all materials used are of the approved type and of the specified quality.

b)To check and assess temporary works by the contractor for safety and compliance with regulations.

c)To check service routes and contractor’s setting out and report any deviations to the consultant team.

d)To check on site that all installation works are of the approved methods.

e)To check on site that all material and equipment used have been approved by the Architect / M&E / C&S Engineer.

f)To ensure that contractors shall not proceed to the next stage of construction/installation if work is not in accordance with specification, approved method, or design.

g)To witness tests carried out by contractors and record the results, and assisting in testing and commissioning of all M&E systems.

h)You shall ensure that all reinforcement, formwork, penetrations, etc. are finally checked by you prior to concreting. All concrete pours during office hours and all critical pours even after office hours shall be supervised by you personally (i.e. standing supervision).

i)To record all variations as instructed or approved by the consultant team.

j)To inspect and take over completed works.

k)To manage and control a team of site staff or Resident Technical Officer(s).

l)Assist in coordinating Contrator’s works, attending meetings, and ensuring compliance with regulations.

3)COST AND RECORDS

a)To record collate and file all incoming and outgoing design, shop, construction, and coordination drawings. All old construction drawings shall be stamped ‘superseded’ and no checking shall be carried out on the superseded drawings.

b)To record, collate and file all incoming and outgoing mail pertaining to your scope of work.

c)To check and record the contractor’s site progress. The site supervisory staff shall be required to submit daily progress report to the Consultants at specified intervals.

d)To maintain proper and updated daily record of all works done on site, including records of tests, inspections, status of work, safety, site diary, material and equipment on site, labour, dayworks, provisional quantities, etc. and all other records as directed by Building Control Authorities.

e)To check that contractor executes preliminaries items.

f)To generate defects list, supervise and monitor progress of rectification works and ensure that all defects are rectified as per Consultant’s advice.

g)To advise the Consultants on the percentage of works completed for the purpose of verifying progress payment valuation.

h)To check contractor’s claims and variation orders. Actual site checks and measurements shall be carried out.

i)To ensure that the contractors record accurately on drawings, the installation works on site. This is to ensure that the as-built drawings reflect accurately the work that has been done on site. Also to check against the consultants’ drawings and identify and highlight the changes of variation orders so that consultants can direct the contractor to finalise the as-built drawings.

4)WORK PERFORMANCE

a)Knowledge of Work

b)Quality of Work

c)Work Output

d)Organizational Ability

e)Team Work

f)Sense of Responsibility

g)Commitment to Job

h)Initiative

i)Reaction under Pressure

j)Language Ability

k)Conduct

l)Integrity

m)Site Safety

5)MANAGERIAL / SUPERVISORY SKILLS

a)Setting Objective

b)Leadership

c)Power of Analysis

d)Resource Management

a) PCs to manage the day-to-day works assigned to the RTOs and STOs and maintain the records of their respective deployment.

b) Provide administrative support on all matters relating to the Contract including the processing of monthly progress claim payment.

c) Prepare the operations plan (template of which will be provided by the Board later) to facilitate the shutdown of watermains for connection of the newly laid watermains and capping of the watermains to be abandoned and submit for the Board’s approval 2 weeks prior to the estimated date of the linkup. The PC shall make the necessary amendments to the operations plan as requested by the Board, where necessary.

d) Monitor the appointed third-party Contractor’s site progress, performance and maintain a site record to keep track of site progression related to the watermains diversion and pipe laying works.

e) Assist to verify documentation submissions submitted by the appointed third-party Contractor to ensure compliance to the Board’s Specifications.

f) Work closely with the STO to verify the final as-built submission by the appointed third-party Contractor to ensure that the pipe alignment corresponds to the site alignment and the data are properly captured in the WNet (used by PUB to capture the coordinates of the pipe alignment) document.

g) Assist in monitoring all the required documents submission – to facilitate the handover of the complete rectification works, that are carried out by the appointed third-party Contractor.

h) The PC shall be assigned any other administrative works by the Board from time to time as may be specified.

a) Minimum Diploma in Mechanical / Electrical Engineering

1. To study the contract documents and drawings and verify if there are any discrepancies

among the drawings. All discrepancies shall be brought to the attention of the design team

concerned.

2. Liaise with the contractors/sub-contractors in the coordination of site works

3. Ensure the contractors maintain work safety, cleanliness and tidiness of the site

4. To ensure that all installation methods and materials used are in accordance with the

contract drawings and specifications.

5. To liaise with the contractors and design team in the checking and approval of shop

drawings, catalogues and samples.

6. To liaise with the contractors for the witnessing, inspection and coordination of site works where required.

7. To supervise the construction of mechanical and electrical works, and work with other resident supervisory staff deployed on site for successful completion of the Project;

8. To generate defects list, supervise and monitor progress of rectification works and ensure

all defects are rectified.

9. To follow up on site for the Consultant comments on shop/as-built drawings.

10. To check operation and maintenance manuals.

11. To assist in handing over of the installations to the Employer's maintenance staff.

12. To undertake any other duties related to the project as and when instructed by the

Employer.

13. For Acceptance Inspection and Commissioning Tests, all test reports and certificates shall be endorse by the site staff (RTO) and shall be forwarded to Architects/S.O. or employers representative for review and acceptance.

14. To supervise the execution of the Works and ensure that the Works are carried out by the Contractor in accordance to the specification / bills of quantities, drawings and all other contract documents and shall exercise all necessary supervision to ensure Employer’s interest are protected during the course of duty. In connection herewith, the Consultant shall engage the approved number of full-time residential technical officer (RTO) to carry out the supervision of the installation of the mechanical and electrical works during the contract period including any extension of time. They shall directly report to the Consultant.

15. To prepare weekly and monthly site inspection and progress reports for the Consultant.

16. To maintain records of all site correspondences and inspections records.

17. To verify site installations and work done on site, to facilitate progress claims made by the Contractor.

Responsibilities:
• The project manager is responsible for the project management, execution, supervision, coordination and successful completion of the Cooling system project comprising revamping
activities of the water side (chilled water production) and air side (AHU, FCU) with an energy
management system (EMS) migration.
• To ensure compliance with Client and Health & Safety policies and procedures.
• To manage the project within budget, schedule and quality according to the project's contractual
and technical requirements.
• To manage the project engineers.
• To manage and co-ordinate the works of the multiple contractors (Mechanical, Electrical, EMS)
and to ensure they deliver as per plan
• To work with the Regional Project Delivery Office, Engineering department, EMS Manager, project
site engineers, Health & Safety team, procurement team.
• To liaise with the client, consultants, contractors and equipment suppliers.
• To update and maintain the project schedule with the support of Project Delivery Office, the project
engineers, suppliers and contractors.
• To prepare the necessary project reports (progress, cost, Health & Safety) for regular senior
management meetings.
• To attend regular project meetings with client, consultants and contractors on all matters relating to
the project execution and co-ordination.
• Conduct periodic safety inspections and attend project and company's Health & Safety
(H&S) meetings.
• To identify potential opportunities bringing cost margin improvement

Requirements *:

• Minimum Degree in Mechanical or Electrical Engineering or related fields. • Min.10 years of working experience in local Singapore M&E construction industry. • Min. 5 years’ experience as project manager in Chilled Water system and airside cooling systems (AHU, FCU or ACMV. • Experience in brown field projects, A&A projects of above S$15mil contract value. • Knowledge of EMS systems. • Knowledge of BCA Green Mark requirements. • Excellent safety mindset and displays excellent Workplace Health & safety behaviour and records. • Good communication skills, ability to properly communicate with all stakeholders (project team, subordinates, workers, management, sub-contractors, main contractor, client). • Able to prioritise tasks and to articulate issues in a simple way. • Self-motivated, autonomous and able to work under pressure. • Knowledge of building code of practices in Singapore.

Context

• There would be 2 projects • A&A type projects • Night time works involved - not requested for the PM to work night time

• Total portfolio of around SGD20M • Both projects are located near Changi airport and in downtown area. • Project 1 completion date planned for July 2025 • Project 2 completion date planned for Dec 2025

Responsibilities:
• The project manager is responsible for the project management, execution, supervision, coordination and successful completion of the Cooling system project comprising revamping
activities of the water side (chilled water production) and air side (AHU, FCU) with an energy
management system (EMS) migration.
• To ensure compliance with Client and Health & Safety policies and procedures.
• To manage the project within budget, schedule and quality according to the project's contractual
and technical requirements.
• To manage the project engineers.
• To manage and co-ordinate the works of the multiple contractors (Mechanical, Electrical, EMS)
and to ensure they deliver as per plan
• To work with the Regional Project Delivery Office, Engineering department, EMS Manager, project
site engineers, Health & Safety team, procurement team.
• To liaise with the client, consultants, contractors and equipment suppliers.
• To update and maintain the project schedule with the support of Project Delivery Office, the project
engineers, suppliers and contractors.
• To prepare the necessary project reports (progress, cost, Health & Safety) for regular senior
management meetings.
• To attend regular project meetings with client, consultants and contractors on all matters relating to
the project execution and co-ordination.
• Conduct periodic safety inspections and attend project and company's Health & Safety
(H&S) meetings.
• To identify potential opportunities bringing cost margin improvement

Requirements *:

• Minimum Degree in Mechanical or Electrical Engineering or related fields. • Min.10 years of working experience in local Singapore M&E construction industry. • Min. 5 years’ experience as project manager in Chilled Water system and airside cooling systems (AHU, FCU or ACMV. • Experience in brown field projects, A&A projects of above S$15mil contract value. • Knowledge of EMS systems. • Knowledge of BCA Green Mark requirements. • Excellent safety mindset and displays excellent Workplace Health & safety behaviour and records. • Good communication skills, ability to properly communicate with all stakeholders (project team, subordinates, workers, management, sub-contractors, main contractor, client). • Able to prioritise tasks and to articulate issues in a simple way. • Self-motivated, autonomous and able to work under pressure. • Knowledge of building code of practices in Singapore.

Context

• There would be 2 projects • A&A type projects • Night time works involved - not requested for the PM to work night time

• Total portfolio of around SGD20M • Both projects are located near Changi airport and in downtown area. • Project 1 completion date planned for July 2025 • Project 2 completion date planned for Dec 2025

Planning and Coordination

- Knowledagble in Requirement Management Plan

- Follow up and Update Installation, Test and commissioning documents in accordance to the required specification for external interface.

- Interface clarification and technical integration of all COM systems in the area of installation, Testing and Commissioning (ITC) within the station, wayside and depot, including the interfaces to the existing and other systems.

- Technical clarification and support relate to installation, testing and commissioning with subsystem, customer and consultant. Providing feedback concerning analysis of the technical problem and answering technical inquiries related to ITC.

- Produced and follow up report progress of the work

- Follow internal process to raise any non-conformities found at site. Trouble shooting of the system errors found and liaise with Engineering team for remedial actions.

- Knowledgeable about the CBTC system is preferred

Liaise with procurement and logistics on material deliveries based on the testing to be performed and planned in advance for the pre-requisite

Installation Activities

- have background /experience in installation is preferrence

- Knowledgeable with the quality control process

- knowledgeable about the handover process from installation to test.

Test and Commissioning

Singapore Special Requirements(Optional) if available is better

- having a LEW license is preference

- have brown fieild experience

- Having a good knowledge from train delivery and manage to undergo installation, static and dynamic testing.

General Requirements:

- Knowledgde with linux, windows operating system and command line.

- Knowledge in networking

- Knowledge in electrical and software troubleshooting.

- good knowledge about integration for wayside and vehicle testing

- Knowledge of installation, testing and commissioning activities

- Knowledge of relevant European and International Standards

- Knowledge of engineering processes

- Experience in project realization, preferably in an international project environment

- Experience in planning, installation, testing and commissioning of telecommunication and/ or fare collection railway is preferable

- Intercultural experience

- Knowledgeable with the cisco switch configuration

- Knowledgeable how to use the RF test tool, LAN cable tester, F/O OTDR tester and read the result.

- Experience of work on or around railway tracks and on vehicles.

- Good knowledge about routines after replacement and repairs of equipment.

- Good knowledge and understanding of the ITC process.

- Good knowledge about applicable test methods.

- Able to read and interpret drawings and circuit diagrams

- Good knowledge about EMC

- good knowledge with interlocking testing

- Good command of English

- Good knowledge about integration testing with wayside signalling system and other external interface(SCADA, Telecom and etc. )

Job Responsibility

(Specific Skills)

- Knowledeable with wayside system

- Knowledgeable with Vehicle signalling system

Generic Skills

- Assure sites are properly stocked with test tools. And test tools are periodically calibrated per AT standards.

-Participate in the Factory Acceptance Testing in the lab and preparation of FAT plan.

- Lead site commissioning activities of radio-based train control systems, including Functional tests and System Acceptance Test (SAT) and System Integration Test (SIT) and ensure that all interfaces to the signalling system are appropriately tested.

- Lead test and commissioning of the On-Board, Wayside, and Radio system system

- Liaise with Engineering / supplier for any design changes and modifications necessary subject to test results

- Record, report, and endorse test results when appropriate.

- Ensuring that testing activities are carried out in timely, logical and cost effective manners.

- Work with Engineering team for the evolution of drawings (ie. mark-up, change order, and transmittals) until the as-build stage.

- Develop productive relationships with client’s teams to ensure successful handover and post-implementation operation of projects.

- Plan and schedule site ITC activities in accordance to the rolling programme, that align with the master programme

- Produce red correction based on the released drawings and

- Correct and rectify failures occurs during T&C phase.

- Raise NCR(None Confirmity) / MNCR (Material None Confirmty) / Fault report during fault found.

- Conolidate / track the following; records, software, hardwares, field changes.

- Implement field change orders

- Prepare installation and test and commissioning procedures / method statement for the communication-based train control system

- Verify the quality of installation works and raise concern if there is a quality issue.

- Troubleshooting, analysis in case of any issues encountered.

- Able to have a good collaboration with the vehicle testers and wayside testers during interface testing.

- Lead / Support the department for the payment milestones related to the test and commissioning

a) Minimum Diploma in Mechanical / Electrical Engineering

b) Min. 3 years experience in Water pipeline project

1. To act as a Site Supervisor appointed by the Qualified Person (QP) in accordance with the Building Control Act.

2. To assist the QP in carrying out supervision works on site

3. To prepare inspection and test plans which are relevant for the supervision of the projects.

4. To conduct quality control of all mechanical & electrical

5. To inspect and advise for compliance by Contractor.

6. To support in public relations works.

7. To supervise and keep independent records of day works including overall and part works programme.

8. To issue site memo to Contractor for recording of observed safety and quality non-compliance with Contract or Authorities, Services Agencies requirements.

9. To attend project meetings and draft meeting minutes.

10. To carry out site supervision and inspection of works including any off-site manufacturing/testing as instructed by the QP and/or S.O. so as to ensure that works are constructed to the required quality, accuracy and standards.

11. To monitor progress of the works on site including material supply to the site and at any off-site manufacturing/testing facilities and report delays immediately.

12. To provide standing supervision in compliance with the relevant Building Control Regulations.

13. To maintain proper and updated daily records of all works done, including independent record of test, inspections, status of work, safety, site diary, material and equipment on site, labour, dayworks, provisional quantities etc.

14. To check that the Contractor executes preliminary items.

15. To check service routes and Contractor’s setting out and report any deviations to the QP/S.O.

16. To verify reports and claims submitted by Contractors.

17. To record all variations as instructed or approved by the S.O.

18. To undertake any other duties related to the project as and when instructed by the S.O./Client/QP.

19. To check drawings including as-built and documents and report discrepancies.

20. Report on site safety, security and housekeeping.

21. Verification of the Client’s Permit To Works (CPTW) checklist completed by the Contractor including:

i. Review the CPTW and keep records of relevant documents such as Authorities/Agencies

approvals, services detection plan and etc. on site.

ii. Make yourself aware of the contractor daily site works and remind them to provide the CPTW

for your verification prior to commencing works on site.

iii. Inform the Contractor in-writing of any non-compliance identified by the CPTW and ensure that

the Contractor rectify the non-compliance prior to permitting works to commence.

iv. Inform the S.O./ QP immediately if the Contractor proceeded works on site without a valid CPTW.

22. Any others duties specified under Building Control Acts and relevant scope

23. Any other work incidental to the above and/or reasonably to be inferred from the nature of work to be carried out by the Service Provider Field staff; and,

24. Such other work as may be agreed from time to time.

25. In addition to the principal duties detailed above, the Field Staff is expected to be vigilant and monitor the Contractor performance in progress, site safety, services protection, security and hygiene.

Planning and Coordination

- Knowledagble in Requirement Management Plan

- Follow up and Update Installation, Test and commissioning documents in accordance to the required specification for external interface.

- Interface clarification and technical integration of all COM systems in the area of installation, Testing and Commissioning (ITC) within the station, wayside and depot, including the interfaces to the existing and other systems.

- Technical clarification and support relate to installation, testing and commissioning with subsystem, customer and consultant. Providing feedback concerning analysis of the technical problem and answering technical inquiries related to ITC.

- Produced and follow up report progress of the work

- Follow internal process to raise any non-conformities found at site. Trouble shooting of the system errors found and liaise with Engineering team for remedial actions.

- Knowledgeable about the CBTC system is preferred

Liaise with procurement and logistics on material deliveries based on the testing to be performed and planned in advance for the pre-requisite

Installation Activities

- have background /experience in installation is preferrence

- Knowledgeable with the quality control process

- knowledgeable about the handover process from installation to test.

Test and Commissioning

Singapore Special Requirements(Optional) if available is better

- having a LEW license is preference

- have brown fieild experience

- Having a good knowledge from train delivery and manage to undergo installation, static and dynamic testing.

General Requirements:

- Knowledgde with linux, windows operating system and command line.

- Knowledge in networking

- Knowledge in electrical and software troubleshooting.

- good knowledge about integration for wayside and vehicle testing

- Knowledge of installation, testing and commissioning activities

- Knowledge of relevant European and International Standards

- Knowledge of engineering processes

- Experience in project realization, preferably in an international project environment

- Experience in planning, installation, testing and commissioning of telecommunication and/ or fare collection railway is preferable

- Intercultural experience

- Knowledgeable with the cisco switch configuration

- Knowledgeable how to use the RF test tool, LAN cable tester, F/O OTDR tester and read the result.

- Experience of work on or around railway tracks and on vehicles.

- Good knowledge about routines after replacement and repairs of equipment.

- Good knowledge and understanding of the ITC process.

- Good knowledge about applicable test methods.

- Able to read and interpret drawings and circuit diagrams

- Good knowledge about EMC

- good knowledge with interlocking testing

- Good command of English

- Good knowledge about integration testing with wayside signalling system and other external interface(SCADA, Telecom and etc. )

Job Responsibility

(Specific Skills)

- Knowledeable with wayside system

- Knowledgeable with Vehicle signalling system

Generic Skills

- Assure sites are properly stocked with test tools. And test tools are periodically calibrated per AT standards.

-Participate in the Factory Acceptance Testing in the lab and preparation of FAT plan.

- Lead site commissioning activities of radio-based train control systems, including Functional tests and System Acceptance Test (SAT) and System Integration Test (SIT) and ensure that all interfaces to the signalling system are appropriately tested.

- Lead test and commissioning of the On-Board, Wayside, and Radio system system

- Liaise with Engineering / supplier for any design changes and modifications necessary subject to test results

- Record, report, and endorse test results when appropriate.

- Ensuring that testing activities are carried out in timely, logical and cost effective manners.

- Work with Engineering team for the evolution of drawings (ie. mark-up, change order, and transmittals) until the as-build stage.

- Develop productive relationships with client’s teams to ensure successful handover and post-implementation operation of projects.

- Plan and schedule site ITC activities in accordance to the rolling programme, that align with the master programme

- Produce red correction based on the released drawings and

- Correct and rectify failures occurs during T&C phase.

- Raise NCR(None Confirmity) / MNCR (Material None Confirmty) / Fault report during fault found.

- Conolidate / track the following; records, software, hardwares, field changes.

- Implement field change orders

- Prepare installation and test and commissioning procedures / method statement for the communication-based train control system

- Verify the quality of installation works and raise concern if there is a quality issue.

- Troubleshooting, analysis in case of any issues encountered.

- Able to have a good collaboration with the vehicle testers and wayside testers during interface testing.

- Lead / Support the department for the payment milestones related to the test and commissioning

Responsibilities:
• The project manager is responsible for the project management, execution, supervision, coordination and successful completion of the Cooling system project comprising revamping
activities of the water side (chilled water production) and air side (AHU, FCU) with an energy
management system (EMS) migration.
• To ensure compliance with Client and Health & Safety policies and procedures.
• To manage the project within budget, schedule and quality according to the project's contractual
and technical requirements.
• To manage the project engineers.
• To manage and co-ordinate the works of the multiple contractors (Mechanical, Electrical, EMS)
and to ensure they deliver as per plan
• To work with the Regional Project Delivery Office, Engineering department, EMS Manager, project
site engineers, Health & Safety team, procurement team.
• To liaise with the client, consultants, contractors and equipment suppliers.
• To update and maintain the project schedule with the support of Project Delivery Office, the project
engineers, suppliers and contractors.
• To prepare the necessary project reports (progress, cost, Health & Safety) for regular senior
management meetings.
• To attend regular project meetings with client, consultants and contractors on all matters relating to
the project execution and co-ordination.
• Conduct periodic safety inspections and attend project and company's Health & Safety
(H&S) meetings.
• To identify potential opportunities bringing cost margin improvement

Requirements *:

• Minimum Degree in Mechanical or Electrical Engineering or related fields. • Min.10 years of working experience in local Singapore M&E construction industry. • Min. 5 years’ experience as project manager in Chilled Water system and airside cooling systems (AHU, FCU or ACMV. • Experience in brown field projects, A&A projects of above S$15mil contract value. • Knowledge of EMS systems. • Knowledge of BCA Green Mark requirements. • Excellent safety mindset and displays excellent Workplace Health & safety behaviour and records. • Good communication skills, ability to properly communicate with all stakeholders (project team, subordinates, workers, management, sub-contractors, main contractor, client). • Able to prioritise tasks and to articulate issues in a simple way. • Self-motivated, autonomous and able to work under pressure. • Knowledge of building code of practices in Singapore.

Context

• There would be 2 projects • A&A type projects • Night time works involved - not requested for the PM to work night time

• Total portfolio of around SGD20M • Both projects are located near Changi airport and in downtown area. • Project 1 completion date planned for July 2025 • Project 2 completion date planned for Dec 2025

a) PCs to manage the day-to-day works assigned to the RTOs and STOs and maintain the records of their respective deployment.

b) Provide administrative support on all matters relating to the Contract including the processing of monthly progress claim payment.

c) Prepare the operations plan (template of which will be provided by the Board later) to facilitate the shutdown of watermains for connection of the newly laid watermains and capping of the watermains to be abandoned and submit for the Board’s approval 2 weeks prior to the estimated date of the linkup. The PC shall make the necessary amendments to the operations plan as requested by the Board, where necessary.

d) Monitor the appointed third-party Contractor’s site progress, performance and maintain a site record to keep track of site progression related to the watermains diversion and pipe laying works.

e) Assist to verify documentation submissions submitted by the appointed third-party Contractor to ensure compliance to the Board’s Specifications.

f) Work closely with the STO to verify the final as-built submission by the appointed third-party Contractor to ensure that the pipe alignment corresponds to the site alignment and the data are properly captured in the WNet (used by PUB to capture the coordinates of the pipe alignment) document.

g) Assist in monitoring all the required documents submission – to facilitate the handover of the complete rectification works, that are carried out by the appointed third-party Contractor.

h) The PC shall be assigned any other administrative works by the Board from time to time as may be specified.

a) Minimum Diploma in Mechanical / Electrical Engineering

b) Min. 3 years experience in Water pipeline project

1. To act as a Site Supervisor appointed by the Qualified Person (QP) in accordance with the Building Control Act.

2. To assist the QP in carrying out supervision works on site

3. To prepare inspection and test plans which are relevant for the supervision of the projects.

4. To conduct quality control of all mechanical & electrical

5. To inspect and advise for compliance by Contractor.

6. To support in public relations works.

7. To supervise and keep independent records of day works including overall and part works programme.

8. To issue site memo to Contractor for recording of observed safety and quality non-compliance with Contract or Authorities, Services Agencies requirements.

9. To attend project meetings and draft meeting minutes.

10. To carry out site supervision and inspection of works including any off-site manufacturing/testing as instructed by the QP and/or S.O. so as to ensure that works are constructed to the required quality, accuracy and standards.

11. To monitor progress of the works on site including material supply to the site and at any off-site manufacturing/testing facilities and report delays immediately.

12. To provide standing supervision in compliance with the relevant Building Control Regulations.

13. To maintain proper and updated daily records of all works done, including independent record of test, inspections, status of work, safety, site diary, material and equipment on site, labour, dayworks, provisional quantities etc.

14. To check that the Contractor executes preliminary items.

15. To check service routes and Contractor’s setting out and report any deviations to the QP/S.O.

16. To verify reports and claims submitted by Contractors.

17. To record all variations as instructed or approved by the S.O.

18. To undertake any other duties related to the project as and when instructed by the S.O./Client/QP.

19. To check drawings including as-built and documents and report discrepancies.

20. Report on site safety, security and housekeeping.

21. Verification of the Client’s Permit To Works (CPTW) checklist completed by the Contractor including:

i. Review the CPTW and keep records of relevant documents such as Authorities/Agencies

approvals, services detection plan and etc. on site.

ii. Make yourself aware of the contractor daily site works and remind them to provide the CPTW

for your verification prior to commencing works on site.

iii. Inform the Contractor in-writing of any non-compliance identified by the CPTW and ensure that

the Contractor rectify the non-compliance prior to permitting works to commence.

iv. Inform the S.O./ QP immediately if the Contractor proceeded works on site without a valid CPTW.

22. Any others duties specified under Building Control Acts and relevant scope

23. Any other work incidental to the above and/or reasonably to be inferred from the nature of work to be carried out by the Service Provider Field staff; and,

24. Such other work as may be agreed from time to time.

25. In addition to the principal duties detailed above, the Field Staff is expected to be vigilant and monitor the Contractor performance in progress, site safety, services protection, security and hygiene.

a) PCs to manage the day-to-day works assigned to the RTOs and STOs and maintain the records of their respective deployment.

b) Provide administrative support on all matters relating to the Contract including the processing of monthly progress claim payment.

c) Prepare the operations plan (template of which will be provided by the Board later) to facilitate the shutdown of watermains for connection of the newly laid watermains and capping of the watermains to be abandoned and submit for the Board’s approval 2 weeks prior to the estimated date of the linkup. The PC shall make the necessary amendments to the operations plan as requested by the Board, where necessary.

d) Monitor the appointed third-party Contractor’s site progress, performance and maintain a site record to keep track of site progression related to the watermains diversion and pipe laying works.

e) Assist to verify documentation submissions submitted by the appointed third-party Contractor to ensure compliance to the Board’s Specifications.

f) Work closely with the STO to verify the final as-built submission by the appointed third-party Contractor to ensure that the pipe alignment corresponds to the site alignment and the data are properly captured in the WNet (used by PUB to capture the coordinates of the pipe alignment) document.

g) Assist in monitoring all the required documents submission – to facilitate the handover of the complete rectification works, that are carried out by the appointed third-party Contractor.

h) The PC shall be assigned any other administrative works by the Board from time to time as may be specified.

a) PCs to manage the day-to-day works assigned to the RTOs and STOs and maintain the records of their respective deployment.

b) Provide administrative support on all matters relating to the Contract including the processing of monthly progress claim payment.

c) Prepare the operations plan (template of which will be provided by the Board later) to facilitate the shutdown of watermains for connection of the newly laid watermains and capping of the watermains to be abandoned and submit for the Board’s approval 2 weeks prior to the estimated date of the linkup. The PC shall make the necessary amendments to the operations plan as requested by the Board, where necessary.

d) Monitor the appointed third-party Contractor’s site progress, performance and maintain a site record to keep track of site progression related to the watermains diversion and pipe laying works.

e) Assist to verify documentation submissions submitted by the appointed third-party Contractor to ensure compliance to the Board’s Specifications.

f) Work closely with the STO to verify the final as-built submission by the appointed third-party Contractor to ensure that the pipe alignment corresponds to the site alignment and the data are properly captured in the WNet (used by PUB to capture the coordinates of the pipe alignment) document.

g) Assist in monitoring all the required documents submission – to facilitate the handover of the complete rectification works, that are carried out by the appointed third-party Contractor.

h) The PC shall be assigned any other administrative works by the Board from time to time as may be specified.

a) Minimum Degree in Civil Engineering recognised by PEB

b) Registered Resident Engineer by IES

c) Min. 3 years experience in drainage project or equivelant

1. To act as a Site Supervisor appointed by the Qualified Person (QP) in accordance with the Building Control Act.

2. To assist the QP(Supervision) in carrying out supervision works on site

3. To prepare inspection and test plans which are relevant for the supervision of the projects.

4. To conduct quality control of all civil and structural, as well as, mechanical, electrical, and landscaping works.

5. To inspect and advise for compliance on temporary works, including instrumentation reports by Contractor.

6. To support in public relations works.

7. To supervise and keep independent records of day works including overall and part works programme.

8. To issue site memo to Contractor for recording of observed safety and quality non-compliance with Contract or Authorities, Services Agencies requirements.

9. To attend project meetings and draft meeting minutes.

10. To carry out site supervision and inspection of works including any off-site manufacturing/testing as instructed by the QP(Supervision) and/or S.O. so as to ensure that works are constructed to the required quality, accuracy and standards.

11. To monitor progress of the works on site including material supply to the site and at any off-site manufacturing/testing facilities and report delays immediately.

12. To provide standing supervision in compliance with the relevant Building Control Regulations.

13. To maintain proper and updated daily records of all works done, including independent record of test, inspections, status of work, safety, site diary, material and equipment on site, labour, dayworks, provisional quantities etc.

14. To check that the Contractor executes preliminary items.

15. To check service routes and Contractor’s setting out and report any deviations to the QP(Supervision)/S.O.

16. To verify reports and claims submitted by Contractors.

17. To record all variations as instructed or approved by the S.O.

18. To undertake any other duties related to the project as and when instructed by the S.O./Client/QP(Supervision).

19. To check drawings including as-built and documents and report discrepancies.

20. Report on site safety, security and housekeeping.

21. Verification of the Client’s Permit To Works (CPTW) checklist completed by the Contractor including:

i. Review the CPTW and keep records of relevant documents such as Authorities/Agencies

approvals, services detection plan and etc. on site.

ii. Make yourself aware of the contractor daily site works and remind them to provide the CPTW

for your verification prior to commencing works on site.

iii. Inform the Contractor in-writing of any non-compliance identified by the CPTW and ensure that

the Contractor rectify the non-compliance prior to permitting works to commence.

iv. Inform the S.O./ QP(Supervision) immediately if the Contractor proceeded works on site without a valid CPTW.

22. Any others duties specified under Building Control Acts and relevant scope

23. Any other work incidental to the above and/or reasonably to be inferred from the nature of work to be carried out by the Service Provider Field staff; and,

24. Such other work as may be agreed from time to time.

25. In addition to the principal duties detailed above, the Field Staff is expected to be vigilant and monitor the Contractor performance in progress, site safety, services protection, security and hygiene.